ABB A44 112-100
CT/VT-connected DIN energy metering with RS-485: select the Steel variant, set transformer ratios and verify a literal-address voltage read.
- Energy meters
Meters, sensors and controllers, and how each connects to Edge.
394 device pages · 121 manufacturers with device pages
398 devices
CT/VT-connected DIN energy metering with RS-485: select the Steel variant, set transformer ratios and verify a literal-address voltage read.
A single-phase 65 A direct-connected meter with built-in RS-485 and an explicit wire-address rule for its read-only electrical values.
D11 and D13 are direct-connected DIN-rail meters with different phase and current ratings. Their Modbus variants share an integer register map with four-register energy counters and explicit invalid-value markers.
CT-connected panel metering over built-in RS-485, with M1M-specific register types and a read-only voltage check.
96 × 96 mm panel network analyser with CT inputs. M2M MODBUS, ALARM and I/O have RS-485 Modbus RTU; M2M ETHERNET has Modbus TCP. One hexadecimal map of 32-bit integers.
Panel energy monitoring with conventional CTs, two digital outputs and RS-485: exact M4M20RS485 setup and a scaled-integer Modbus read.
M4M 30 Modbus is a panel network analyser for conventional 1 A or 5 A CTs, with RS-485, Bluetooth commissioning and four programmable I/O. Edge reads its scaled electrical values over Modbus RTU.
72 × 72 mm panel meter for DC voltage, bidirectional current, power, energy and ampere-hours, with shunt, Hall effect or direct inputs. The optional RS-485 port runs Modbus RTU: floats from 0x0200 and energy counters from 0x0300, read with FC03.
Three-phase DIN-rail power and energy meter for 5A/1A, 333 mV, mA or Rogowski current transformers, with a built-in RS-485 port running Modbus RTU by default and a published register map including a SunSpec block.
DIN-rail multi-circuit meter for up to 18 single-phase or 6 three-phase circuits behind one incoming supply. Modbus RTU on RS-485, or Modbus TCP on the WEB option, gives per-channel floats from 0x2100 and 0.1 kWh energy counters from 0x2500.
IEC 61000-4-30 Class A power quality and class 0.1S energy meter with two Ethernet ports, RS-485 and USB. Modbus TCP and RTU serve 32-bit floats read with FC03; energy is in 64-bit registers or BACnet/IP Analog Inputs.
Three-phase panel or DIN-rail power meter with a built-in RS-485 port running Modbus RTU. Measurements are 32-bit floats from 0x4000, high word first, read with FC03; energy counters start at 0x4048.
Three-phase panel or DIN-rail power meter with a built-in RS-485 port running Modbus RTU. Measurements are 32-bit floats sent high word first, read with FC03 from hexadecimal addresses such as 0x4002.
Three-phase DIN-rail energy meter, direct-connected 10(80) A or CT-operated 1(6) A, with an RS-485 Modbus RTU port and a hexadecimal FC03 register map.
Direct-connected 80 A three-phase MID meter in four DIN modules with built-in RS-485 Modbus RTU/ASCII. Algodue publishes the register table, with two integer register sets and a floating-point block.
Monitor the Alpha ESS STORION-H29.9, H30 and H50-G3 all-in-one C&I cabinets with EpiSensor Edge: the EMS Modbus TCP dispatching interface, the AC feeder and the control boundary.
Monitor LINAX PQ5000 over Modbus TCP with a first frequency read, documented float decoding and local-interface checks.
Multifunctional power measurement devices from Camille Bauer Metrawatt, sold through Gossen Metrawatt, with a TFT display, Modbus TCP on Ethernet and optional Modbus RTU on RS-485.
Panel-mount controllers for stand-alone refrigeration units, cold rooms and cabinets. With an IROPZ485 serial card in the programming key connector they answer Modbus RTU with probes, alarms and defrost state.
DIN-rail controller for display cases and cold rooms, in Master and Slave boards. The Master's RS485 port answers Modbus RTU for itself and up to five Slaves.
Programmable controllers for supermarket and cold-store compressor racks, managing up to two suction and two condensing lines. Their BMS serial port answers Modbus RTU once the protocol is set to MODBUS SLAVE.
Read the EM24-DIN RS-485 meter with Edge: distinguish direct and CT inputs, import the 32-point map and verify signed, word-swapped measurements.
Single-phase direct-connected Modbus meter with a low-word-first integer read and a 32 A connection boundary.
Three-phase CT-operated energy analyser for DIN rail or 72 x 72 panel. The S option adds an RS-485 Modbus RTU port with a read-only INT32 map sent low word first.
No devices match your filters
Try a broader model fragment, manufacturer or application.
Built from public Zigbee, LoRaWAN and Modbus device definitions and manufacturer documents, including BACnet/IP guides. Exact manufacturer and model identities are joined; similar names are never assumed to be the same device.
Each device page explains the documented connection to Edge, what the device reports and how to check its setup. An Edge template is offered only where an exact reviewed import is available.
Every page cites its sources. Zigbee device photographs come from the Zigbee2MQTT project and are credited under each photograph. We never run code from these sources, and register maps are for reading: never write to a meter from a map on this site.
Tell us the manufacturer and model, and we'll look at its documentation.