INTILION scalepac

Commercial battery energy storage system

INTILION’s 2025 scalepac4/8 brochure describes outdoor LFP configurations from 1.016 MWh and 500 kVA, built from 254 kWh units. The current product page also advertises systems starting from 500 kWh. The INTILION Application Unit provides a customer interface with Modbus TCP/IP; its project point list supplies the monitoring addresses and units, and Edge reads it over Modbus TCP.

INTILION scalepac
  • Modbus TCP
  • IEC 60870-5-101
  • IEC 60870-5-104

Commercial battery energy storage system

Ask an engineer

Compatibility

Compatible with EpiSensor Edge over Modbus TCP through the IAU customer interface

The 2025 brochure documents Modbus TCP/IP and a customer interface on the INTILION Application Unit, alongside IEC 60870-5-101/104 for grid operators. Edge is a Modbus TCP client and reads the customer interface; the project point list supplies the addresses, data types and units.

Current INTILION scalepac family with the INTILION Application Unit only. Site check: obtain the IAU customer-interface point list for the installed IAU version, and record the scalepac unit count, PCS configuration, battery version, firmware and commissioned application. Do not transfer this guide to scalebloc, scalecube or project-specific third-party components.

Connect it with

On any scalepac system, through the customer-side interface of its INTILION Application Unit

  • Wired
  • Edge
  • Platforms
Commercial battery energy storage system
Interface
Gateway
Edge
Output
scalepacscalepac storage units and PCS
INTILION Application UnitCoordinates the storage units and serves the customer interface
ZGW-20 GatewayHosts Edge locally
EpiSensor EdgeModbus client + register map
Customer platformMQTT · API · files
INTILION system links
Customer interface, Modbus TCP
Runs locally
Optional onward data
Connect Edge to the IAU customer interface on the protected site network and configure the reads from the project point list. Start with identity, operating state, AC power, energy and alarms, and compare them with the IAU display and the battery AC feeder meter. Leave the trader and grid-operator interfaces with their owners. Read only. The customer-platform output is optional; Edge remains the local system of record.

Models

Download
ModelsInterfaceRoute into Edge
scalepac4 to scalepac8Four to eight 254 kWh all-in-one units, 1.016 to 2.032 MWh nominal, 500 to 1,000 kVA apparent power, supervised by one INTILION Application UnitStart at the IAU customer interface. Obtain its project point list, then compare read-only values with the IAU and the appropriate AC meter.
Single 254 kWh scalepac unitBuilding block listed in the technical tableThe brochure states that the smallest complete system has four units. Do not present a single enclosure as a complete supported site system.
scalebloc and scalecubeEarlier or utility-scale product families with different architecture and project scopeTreat each as a separate product and obtain its own current interface evidence.

Specifications

The brochure tabulates four-to-eight-unit configurations using 254 kWh LFP units, giving 1.016 to 2.032 MWh nominal energy and 914 to 1,828 kWh usable energy at 90% depth of discharge. The tabulated apparent-power limits range from 500 to 1,000 kVA. The current INTILION Application Unit can connect up to 16 units, so the table is not the maximum complete-system size.1

Tabulated energy range
1.016 to 2.032 MWh nominal; 914 to 1,828 kWh usable at 90% depth of discharge1
Tabulated power range
Up to 500 kVA for scalepac4 and up to 1,000 kVA for scalepac8; customer-specific nominal power from 500 kVA in approximately 125 kVA steps; 0.5 P maximum charge and discharge power1
Battery
Prismatic 306 Ah LFP cells; 254 kWh nominal per unit; more than 6,000 cycles stated1
Published communications
Modbus TCP/IP, remote-control protocols and cloud connection; IAU customer, trader, generation and grid-operator interfaces1
Grid-operator protocols
IEC 60870-5-101 and IEC 60870-5-104 are named for individual grid-operator integration1
Electrical connection
400 V three-phase with neutral and protective earth; grid-parallel operation; 110% overload for at least ten minutes1
Enclosure and environment
Climate-controlled IP54 outdoor enclosures with C5 corrosion protection; -20 to +50 °C with derating above 40 °C; up to 3,000 m altitude12

Interface

Documented measurements and integration boundaries for scalepac.

  • Potential identity, communications state, availability, operating mode and alarms require the approved IAU customer-interface map.
  • Potential AC power, import and export energy, state of charge, state of health and available charge or discharge power must retain source, sign, unit, quality and freshness.
  • Unit, PCS, battery, IAU, site-meter, trader and grid-operator values are separate measurement boundaries and must not be collapsed into one generic BESS point.
  • No charge, discharge, market, power-plant-controller or grid-service command is approved by this guide.

Assessment

Current INTILION scalepac family with IAU; read-only monitoring through the customer interface, with no writes, market participation or grid-compliance claim.

InteroperabilityLimited
The brochure documents relevant protocols and distinct customer, trader and grid-operator interfaces. A project point list is needed for actual addresses; no public register table was found.1
AccuracyNot yet assessed
The public brochure does not list the readable point set, units, sign, quality, accuracy or freshness; they come from the customer-interface point list.
SecurityLimited
The brochure states that cloud data is stored on Western European servers, but it does not define authentication, roles or network hardening for the local customer interface.1
ReliabilityNot yet assessed
Independent-unit operation and 24/7 vendor monitoring are described; the brochure does not describe client recovery, buffering or data retention for the customer interface.1
RuggednessSupported with conditions
IP54, C5 corrosion protection, temperature and altitude limits are published for the current outdoor system.12
ScalabilityLimited
The brochure defines four-to-eight-unit standard systems and up to 16 units per current IAU, but external client count, polling capacity and multi-system point ownership are not published.1
LifecycleSupported with conditions
INTILION publishes a current product page, brochure, expected life of at least 15 years and service packages. Record configuration, firmware, warranty and service for each installation.12

Setup

  1. Confirm the delivered system

    Capture every scalepac enclosure, PCS and battery identity, the IAU hardware and firmware, the commissioned application, meter arrangement and service boundary.

  2. Place the meters on the site diagram

    The IAU supports up to five energy meters for sum and difference measurements. Label the grid connection, battery AC feeder, local generation and any separately metered load. Record each meter’s import direction and whether it measures one feeder or the whole site. Keep the customer, trader and grid-operator interfaces separate.

  3. Read through the customer interface

    Use the 2025 brochure’s customer-side data interface as the starting point. Ask INTILION for the project endpoint and point list: addresses, data types, scale factors, units and power direction. Select identity, operating state, AC power, energy and alarms where supplied. Start with reads only and compare values with the local display; record the installed IAU version once in the commissioning sheet.

  4. Compare battery and grid measurements

    Compare IAU battery power with the battery AC feeder meter over the same interval. Compare the grid meter separately: it includes the site loads and local generation, so it should not normally equal battery power. Check import and export signs during an existing scheduled charge and discharge, without sending a new command. For sum or difference measurements, verify the contributing meters before interpreting the calculated total.

  5. Treat every command as a safety case

    For any later approved setpoint, document owner, range, ramp, interlocks, timeout, local override, rejection feedback, safe fallback and measured connection-point response.

Common questions

Does INTILION scalepac publish Modbus?
Yes. The current brochure lists Modbus TCP/IP among its communication standards, and Edge reads the IAU customer interface over Modbus TCP. The brochure does not publish the customer point map, so take addresses and access rules from the project point list.1
Can Edge command scalepac from this guide?
No. An approved command path needs the exact writable object, units, range, ramp, interlocks, timeout, rejection feedback and safe fallback. The public brochure does not provide that contract.1
Is scalepac a single 254 kWh system?
The brochure lists a 254 kWh enclosure as the building block, but states that the smallest complete system has four units. Its technical table starts the system range at 1.016 MWh and 500 kVA.1
Do IEC 60870-5-101 and IEC 60870-5-104 prove a customer monitoring path?
No. The brochure names those protocols for individual grid-operator integration, and Edge does not use them. Customer monitoring uses the Modbus TCP customer interface.1