Find meters, sensors and controllers by manufacturer, protocol and application, then see the exact route into EpiSensor Edge.
2959 searchable, source-backed device records
ERS Sound measures the average and peak sound pressure level with dBA filtering. It wakes and samples both signals every 10s, and does the final calculation before sending the data at the desired send interval.
ERS VOC is a smart and professional LoRaWAN® sensor for indoor air quality applications. It will measure the levels of the volatile organic compound in the ambient air which says a lot about the general air quality.
Base module of the ELV modular system for building LoRaWAN sensor/actuator nodes from application modules.
GPS/GNSS module of the ELV modular system for position, motion and contact-interface based LoRaWAN tracking. Reports occupancy.
Orientation/motion module of the ELV modular system reporting acceleration, tilt and button events. Reports occupancy.
The EGK-LW20W00 is a battery powered sensor intended for waste level measurement up to 1.5 meters. The device sends collected data over the LoRaWAN® network. The internal timestamp is synced with a downlink.
This compact energy meter can be used for monitoring the power consumption of the load, which can remotely be switched on/off. Equipped with a rechargeable battery for mains outage detection. The internal timestamp is synced with a downlink.
This device reads temperature, humidity, pressure, light intensity, air quality (expressed as IAQ or VOC value) and CO2. 3 traffic light LEDs for air quality display with adjustable brightness.
The MCF-LW12MET is an Enginko mcf88 LoRaWAN sensor with 1-phase energy measurement, which allows to monitor the power, voltage and current of electrical devices. It has an operating temperature of -10 °C to 70 °C and can be used in a variety of applications.
The 4/20mA LoRa sensor allows you to connect an analog 4/20mA probe (not included with the sensor). The signal generated by your 4/20mA probe will be read by the sensor and then sent via LoRa radio.
The level of CO2 is the main indicator of the air quality breathed by the building occupants. This data has a direct influence on the daily comfort of the occupants in enclosed spaces, and can trigger issues such as fatigue, drowsiness, and headaches.
The Enless LoRaWAN CO₂, temperature, and humidity sensor is specifically designed for indoor commercial environments.
This LoRaWAN Open/Closed contact sensor allows you to detect and report status changes on a dry-contact or open collector interface. The digital input sensor can manage two inputs simultaneously.
The Enless LoRaWAN Light, Presence, Temperature, and Humidity Sensor is specifically designed for tertiary and residential indoor environments.
The Enless LoRa pulse sensor allows you to count the pulses of the connected meter. This remote reading sensor can be used with any type of meter that has a dry-contact or open collector output.
The ATEX certified LoRa pulse sensor allows you to count the pulses of the connected gas meter. This remote reading sensor, ATEX certified, Zone 0, can be used with any type of gas meter with a dry contact or open collector output.
The LoRa Enless LED flash reading sensor allows you to count the light flashes (not infrared) from electric meters.
Designed for ambient measurement in tertiary indoor environments, the LoRa(WAN) Enless temperature and humidity sensor allows you to monitor the values necessary for the comfort of building occupants.
The Enless LoRaWAN Temperature and Humidity Sensor is specifically designed to monitor comfort in tertiary environments. It accurately measures ambient temperature and humidity, ensuring a healthy and controlled indoor climate for occupants.
The LoRaWAN temperature and humidity sensor with display is specifically designed for indoor tertiary environments.
The rugged LoRa temperature and humidity sensor can be used in industrial or challenging environments.
The LoRaWAN Enless temperature and humidity sensor is specially designed for commercial indoor environments. It monitors the parameters essential to occupant comfort, such as temperature and humidity, ensuring an optimal indoor climate.
The temperature sensor with external PT1000 contact probe allows to measure temperature at the contact of surfaces.
The temperature sensor is equipped with two external PT1000 contact probes, allowing temperature measurement on contact surfaces. The PT1000 probes provided with the sensor allow measurement of extreme temperatures ranging from -180°C to +250°C.
No devices match your filters
Try a broader model fragment, manufacturer or application.
The database combines maintained Zigbee, LoRaWAN and Modbus sources for discovery. Exact manufacturer and model identities are joined; similar names are never assumed to be the same device.
A source record establishes a documented protocol route. A device page adds the model-specific interface, point map and commissioning steps, and where an Edge template exists it is offered there.
Third-party images are not republished without asset-rights review. Embedded upstream code is never executed. Modbus previews are read-oriented examples and must not be used as the basis for register writes.
